Janitza 1416029 Reactive Power Controller

Reactive Power Controller

Prophi® 12R / 12 RS By pressing the cursor buttons (up / down) the stage display mode can be changed
AUTO MODE ---------------
PROGRAMMING
cosj 1.000 IND
AUTO-INIT* [ NO ]
1 2 3 4 5 6 7 8 9 10 11 12
1
LINE VOLTAGE 230.0 V-L/N
0
LANGUAGE [ ENGLISH ]
16
HARMONICS THD-V [ 7 ] %
1 CURRENT TRANSF.
[ KNOWN ]
2
CURRENT [1] 200.0 A
1
I-CT PRIMARY [ 1000 ] A / X A
16
HARMONICS THD-I [ -,- ] %
2
I-CT PRIMARY [ 1000 ] A / X
3 REACTIVE POWER 88.88 kvar
2
I-CT SECONDARY 1000 A / [5] A
17
HARMONICS [ 3. 5. 7. - 19.]
3
I-CT SECONDARY
4
ACTIVE POWER 88.88 kW
3
END STOPP [12]
4
POWER 1. STAGE [ 25 ].00 kvar
5 APPARENT POWER 88.88 kVA
4
CONTROL SERIES [1] [1 1 1 1 1 1 1 1 1 1 1 1]
2 19
I-CT PRIMARY [ 1000 ] A / X
6 DIFF. REACT POWER 88.88 kvar
5
CONTROL MODE [2] [ INTELLIGENT ]
2 20
I-CT SECONDARY 1000 A / [5] A
7
6
POWER 1. STAGE [ 25 ]. 00 kvar
2 21
END STOPP [12]
TEMPERATURE [1] 25 °C
7
TARGET cos Phi [ 0.98 IND ]
2 22 CONTROL SERIES [1] [1 1 1 1 1 1 1 1 1 1 1 1]
HARMONICS [ 3. ] V: 0.5% - I: 0.1%
8
MEAS. VOLTAGE [ 230 ] V - L/N
2 23 CONTROL MODE [2] [ INTELLIGENT ]
10 HARMONICS THD rel.
V: 0.5% I: 0.3%
9
V - CT RATIO [ NO ]
2 24
POWER 1.STAGE [ 25 ]. 00 kvar
11 SYSTEM-POWER 88.88 kvar
10
SWITCH-IN TIME [ 40 ] sec.
2 25
TARGET cos Phi [ 0.98 IND ]
12
11 SWITCH-OFF TIME [ 40 ] sec.
2 26 SWITCH-IN TIME [ 40 ] sec.
13 DATE - TIME [1] 06.11.2015 - 10:13:40
12
DISCHARGE TIME [ 60 ] sec.
2 27 SWITCH-OFF TIME [ 40 ] sec.
14
13
ALARM TEMP.
[ 55 °C ]
2 28 DISCHARGE TIME [ 60 ] sec.
8
9
FREQUENCY 50.0 Hz
ENERGY [1] 88.88 kWh ( + )
SOFTWARE
VERSION ....
BACK TO 1 After 60 sec. without pressing any button, automatic change to auto-mode
Settings shown with grey background colour are active only in case of certain other settings.
If not needed they are not displayed.
32
14
15
18 CONTRAST *****[4]*****
ALARM RELAY [3] [ ERROR inverse]
29
FAN TEMP.
[ 30 °C ]
Q - OFFSET [ NO ]
BASIC SETTINGS
RESET - NO BACK
- 31 -
1000 / [5] A
TEST 1...3 (automatic TEST RUN)
* AUTO INIT exists only, if in „ExpertMode 2":
„2 Auto-Init Error = YES“
Changing of values by buttons: