SICK 1059054 type: AFM60A-BGEB018X12 Absolute encoder

PERFORMANCEMax. resolution (number of steps per revolution x number of revolutions)18 bit x 12 bit (262,144 x 4,096)Error limits G0.03° 1)Repeatability standard deviation σr0.002° 2)1) In accordance with DIN ISO 1319-1, position of the upper and lower error limit depends on the installation situation, specified value refers to a symmetrical position, i.e. deviation in upper and lower direction is the same.2) In accordance with DIN ISO 55350-13; 68.3% of the measured values are inside the specified area.INTERFACESCommunication interfaceEtherCAT®Communication Interface detailCoE (CAN over EtherCAT®)Encoder profileCiA DS-406Data transmission rate (baud rate)

10 Mbit/s

100 Mbit/s

Transmission mediumCAT-5e cableParameterising dataNumber of steps per revolution, number of revolutions, PRESET, counting direction, samplingrate for speed monitoring, unit for output of the speed value, round axis functionality (multiturnversion only), single or multi access mode, fast dataexchange modeAvailable diagnostics dataCurrent, minimum and maximum temperature, maximum speed, positioning monitoring, power-on counter, operating hours counter for power-on/motion, counter of direction changes/number of movements cw/number of movements ccw, minimum and maximum operating voltage, signal monitoring for single and multiturnInitialization timeApprox. 6 sCycle time125 µs ... 100 msELECTRICAL DATAConnection type

Male connector, 1 x M12, 4-pin, axial

Female connector, 2 x M12, 4-pin, axial

Supply voltage10 ... 30 V DCMTTFd: mean time to dangerous failure80 years (EN ISO 13849-1) 1)1) This product is a standard product and does not constitute a safety component as defined in the Machinery Directive. Calculation based on nominal load of components, average ambient temperature 40°C, frequency of use 8760 h/a. All electronic failures are considered hazardous. For more information, see document no. 8015532.MECHANICAL DATAMechanical designBlind hollow shaftShaft diameter14 mmWeight0.2 kgShaft materialStainless steelHousing materialAluminumStart up torque0.8 NcmOperating torque0.6 NcmPermissible shaft movement, axial static/dynamic± 0.5 mm, ± 0.1 mmPermissible shaft movement, radial static/dynamic± 0.3 mm, ± 0.05 mmMoment of inertia of the rotor40 gcm²Bearing lifetime3.0 x 10^9 revolutionsAngular acceleration≤ 500,000 rad/s²AMBIENT DATAEMCAccording to EN 61000-6-2 and EN 61000-6-3 1)Enclosure rating

IP65, shaft side (according to IEC 60529)

IP67, housing side (according to IEC 60529) 2)

Permissible relative humidity90 % (condensation of the optical scanning not permitted)Operating temperature range–40 °C ... +85 °CStorage temperature range–40 °C ... +100 °C, without packageResistance to shocks100 g, 6 ms (according to EN 60068-2-27)Resistance to vibration30 g, 10 Hz ... 2,000 Hz (according to EN 60068-2-6)1) The EMC according to the standards quoted is achieved if screened cables are used.2) With mating connector inserted.CLASSIFICATIONSECl@ss 5.027270502ECl@ss 5.1.427270502ECl@ss 6.027270590ECl@ss 6.227270590ECl@ss 7.027270502ECl@ss 8.027270502ECl@ss 8.127270502ECl@ss 9.027270502ETIM 5.0EC001486ETIM 6.0EC001486UNSPSC 16.090141112113

لا يوجد وصف عام متاح في الوقت الحالي