Industrial spare parts & engineering solutions since 2001.
德国仓直发，全球快速配送
多种支付方式多种付款选项
Stenflex Type: 12F DN150 Swivel Joint
技术数据表 / 产品文档
| 品牌 |  |
| 类别 | 其他 |
| 产品名称 | Stenflex Type: 12F DN150 Swivel Joint |
| 产品编号 | Stenflex Type: 12F DN150 Swivel Joint |
欢迎联系我们！我们会在 24 个工作小时内（不含周末及节假日）确认库存状态和预计交期。
产品描述
Stenflex的产品（包括Stenflex Type: 12F DN150 Swivel Joint）通过平行进口渠道采购，并快速可靠地交付给United States的客户。Imtek Engineering以具有竞争力的价格提供正品Stenflex零部件。即使Stenflex Type: 12F DN150 Swivel Joint未在我们的网站上列出，您也可以随时申请报价——我们的团队将迅速响应并为您提供专属报价。
United States■ A pressure resistance test according to Annex 1, Section 3.22 of the Pressure Equipment Directive 2014/68/EU is normally not carried out by the manufacturer. This is to be
performed by the user after installation in the piping system (PT = 1.43 x PS).
■ The user is responsible for providing any necessary safety and monitoring facilities (such
as the installation of temperature sensors, pressure-limiting valves, measures for avoiding pressure jolts and liquid hammers).
)VS[PUN[VYX\LZ for STENFLEX® rubber-type expansion joints.
The bolting torques refer to new expansion joints. If required in some cases, the values
can be exceeded by by 30%.
30 %.Enquiries Enquiriesfor forType TypeDDare areto to be be sent sent to
to the the manufacturer.
manufacturer. Tighten the screws several times in a crosswise manner so that an evenly distributed seal-pressing
effect is achieved. After approx. 24 hours of operation, the settling is to be balanced out by
re-tightening the screws. In the unlikely event of a leak the manufacturer must be contacted.
For torques which are not stated please contact the manufacturer.
■ Table in nominal widths including
DN 400 Series A/AR/AS/E/G/R/RS A/AR/AS/E/G/MS/R/RS in nominal widths including
DN and 400 and E Series pressure stages PN 10 and PN 16 tighten screws as needed until there is
no gap between them and the surface (note max. screw tightening torque).
■ Table G Series GR-SAE, use only screws according to DIN 6912.
Nominal width, Bolting torque ■ Table Series W-1 in the pressure ratings PN 1/2,5.
I Nominal width, Bolting torque/Bolting torque ■ Table K Series W-2 in the pressure ratings PN 2,5.
Nominal width, Bolting torque/Bolting torque ■ Table L Series C in the pressure ratings PN 6/10/16.
Nominal width, Bolting torque ■ Table N Series A in the pressure ratings PN 10 and PN 16.
Nominal width, Bolting torque ■ Table O Series B in the pressure ratings PN 10 and PN 16.
Nominal width, Bolting torque
B Installation instructions for axial and universal expansion joints MVYLX\HSPZPUNSLUN[OJOHUNLZ ^ P [ O V \ [WYL[LUZPVUPUN
■ Non-tensioned rubber-type expansion joints can be applied for the combination (superimposition) of axial, lateral and angular movements. Observe the reduction of the
individual movements! If in doubt, consult the manufacturer.
■ Fixed points must definitely be adequately dimensioned. Fixed points must be capable
of coping with the force FFP from the sum of the axial thrust force (F1), the expansion joint
adjusting force (F2) and the frictional forces from the guide bearings (F3) (Fig. ).
■ In principle, o n l y one expansion joint shall be installed between two fixed points.
■ With several axial expansion joints, the pipe pattern must be subdivided by interim fixed
points.
■ The piping with axial expansion joints must be exactly guided with bearings. Guide bearings are to be arranged on both sides of the expansion joint. A fixed point replaces a
guide bearing. Fig. .
17
17
performed by the user after installation in the piping system (PT = 1.43 x PS).
■ The user is responsible for providing any necessary safety and monitoring facilities (such
as the installation of temperature sensors, pressure-limiting valves, measures for avoiding pressure jolts and liquid hammers).
)VS[PUN[VYX\LZ for STENFLEX® rubber-type expansion joints.
The bolting torques refer to new expansion joints. If required in some cases, the values
can be exceeded by by 30%.
30 %.Enquiries Enquiriesfor forType TypeDDare areto to be be sent sent to
to the the manufacturer.
manufacturer. Tighten the screws several times in a crosswise manner so that an evenly distributed seal-pressing
effect is achieved. After approx. 24 hours of operation, the settling is to be balanced out by
re-tightening the screws. In the unlikely event of a leak the manufacturer must be contacted.
For torques which are not stated please contact the manufacturer.
■ Table in nominal widths including
DN 400 Series A/AR/AS/E/G/R/RS A/AR/AS/E/G/MS/R/RS in nominal widths including
DN and 400 and E Series pressure stages PN 10 and PN 16 tighten screws as needed until there is
no gap between them and the surface (note max. screw tightening torque).
■ Table G Series GR-SAE, use only screws according to DIN 6912.
Nominal width, Bolting torque ■ Table Series W-1 in the pressure ratings PN 1/2,5.
I Nominal width, Bolting torque/Bolting torque ■ Table K Series W-2 in the pressure ratings PN 2,5.
Nominal width, Bolting torque/Bolting torque ■ Table L Series C in the pressure ratings PN 6/10/16.
Nominal width, Bolting torque ■ Table N Series A in the pressure ratings PN 10 and PN 16.
Nominal width, Bolting torque ■ Table O Series B in the pressure ratings PN 10 and PN 16.
Nominal width, Bolting torque
B Installation instructions for axial and universal expansion joints MVYLX\HSPZPUNSLUN[OJOHUNLZ ^ P [ O V \ [WYL[LUZPVUPUN
■ Non-tensioned rubber-type expansion joints can be applied for the combination (superimposition) of axial, lateral and angular movements. Observe the reduction of the
individual movements! If in doubt, consult the manufacturer.
■ Fixed points must definitely be adequately dimensioned. Fixed points must be capable
of coping with the force FFP from the sum of the axial thrust force (F1), the expansion joint
adjusting force (F2) and the frictional forces from the guide bearings (F3) (Fig. ).
■ In principle, o n l y one expansion joint shall be installed between two fixed points.
■ With several axial expansion joints, the pipe pattern must be subdivided by interim fixed
points.
■ The piping with axial expansion joints must be exactly guided with bearings. Guide bearings are to be arranged on both sides of the expansion joint. A fixed point replaces a
guide bearing. Fig. .
17
17
常见问题
关于Stenflex品牌Stenflex Type: 12F DN150 Swivel Joint产品的常见问题。Imtek Engineering随时准备帮助您在United States采购Stenflex的Stenflex Type: 12F DN150 Swivel Joint。
Imtek Engineering通过可信赖的供应渠道采购正品Stenflex产品，并以具有竞争力的价格向United States客户提供。
