Bartec 07-1511 Insert Switch

BARTEC OPERATIONAL INSTRUCTION
Explosion protection 0044
Approved Body No.
2503
Technical data Contact Travels Rest position
Certification
IECEx EPS 14.0091 U
LLW
Ex db IIC Gb Ex db I Mb
DW
Marking IECEx
WHG
EPS 14 ATEX 1 765 U
CML 21UKEX1857U
Switching point NLW
Certification
VLW
II 2G Ex db IIC Gb I M2 Ex db I Mb
Marking ATEX / UKEX
Other approvals and certificates, bartec.com
RLW
Notified Body No.
End position
Technical data Service temperature for insert switch
-60 °C to +100 °C (-76 °F to +212 °F) depending on type and used matierals
Contact travels (in mm)
Ambient temperature for limit switch
-60 °C to +90 °C (-76 °F to 194 °F) depending on rated current and temperature class
Pretravel
VLW
max. 0.9
Overtravel
NLW
min. 0.5
Electrical data for control switch in accordance with
DIN EN 60947-5-1
Rated operating voltage Utilization category AC-15 4A AC-15 2A DC-13 0.15 A
Isolation voltage
Differential value
DW
max. 0.45
Reset travel
RLW
0.9
No-load travel
LLW
0.1 bis 0.45
AC switching capacity (at temperature of +40 °C)

ohmic load inductive load cos φ = 0.6 400 V 3A 2A 250 V 5A 3A 30 V 7A 5A
DC switching capacity (at temperature of +40 °C)
AC 400 V 250 V 400 V 250 V 400 V

ohmic load inductive load
L/R = 3 μs 250 V 0.4 A 0.03 A 30 V 7A 5A
Tightening torque of fixing screws
0.6 Nm
Rating of gold-coated contacts
Min. DC 2,4V - 50 mA Max. DC 30V - 4 mA the product of voltage and current should
not exceed 0.12 VA for alternating current these values have to be interpreted as peak values
± 0.02
Repeat accuracy WHG (for repetetive actuation) Service life mechanical
>2 x 106
electrical
dependent on load
max. switching rate
1000 operations/h
Switching actuation force Single-break switch
max. 2.0 N
Double-break switch
max. 3.6 N
Reset force Single-break switch
min. 0.4 N
Double-break switch
min. 0.8 N
Operating rate
> 10 μm/sec.
Contact break distance
2 x ≥ 0.3 mm
Electrical connection
Insert switch cores 0.75 mm2
LO7G-K/Radox
Limit switch cable 0.75 mm2 H05VV-F/A05VV-F/ BETAflam other cores and cables on request
Conductor diameter
2-wire 6.1 ± 0.3 mm 3-wire 6.6 ± 0.3 mm 4-wire 6.7 ± 0.3 mm 6-wire 8.9 ± 0.3 mm
Contact element
snap-action contact element (double-break) as, normally-open, normally-closed,
changeover contact as well as N/0 + N/C contacts for circuits with equal potentials.
Contact material
Silver or gold-coated contacts (all contact elements have a standard protective
gold-coating as standard)
Double-break switch (switch options)
simultaneous switch sequence:
chamber I and II almost simultaneous defined switch sequence:
chamber I switches mechanically safe 0.03 up to 0.3 mm before chamber II
Weight
Insert switch with 500 mm cores:
single-break switch 35 g, double-break switch 70 g Limit switch with 3 m cable:
single-break switch 210 g, double-break switch 415 g
Technical data subject to change without notice.
Housing material
plastic (thermoplastics)
Protection class
IP 66 (IEC/EN 60529)
electrical
dependent on load
Plunger/additional actuator
stainless steel
01-1500-7D0001/B-07/2022-ESS-291766
Page 3/7