SKF CMPT 2310TX15 Sensor

Specifications
47,2 mm (1.86 in.)
Specifications conform to ISA-RP-37.2 (1-95) and are typical values referenced at 24 °C (75 °F), 24 V DC supply, 4 mA constant current
and 80 Hz.
14,0 mm (0.55 in.) 11,0 mm (0.43 in.)
Sensor – Accelerometer (SKF CMPT 2310 and CMPT 2310T) • • • • • • • • •
29,0 mm (1.14 in.)
Sensitivity: 100 mV/g Frequency range: 1 Hz to 10 kHz Sensitivity precision: ±10%
Sensitivity deviation over full temperature range: 10%, approximately –5% at –50 °C (–60 °F) and +5% at +120 °C (+250 °F)
Amplitude linearity: < 1%, up to full scale Transverse sensitivity: ≤ 5% of axial
Acceleration output range: 70 g Shock limit: 5 000 g peak Accelerometer measurement temperature range: –50 to +120 °C
(–60 to +250 °F)
ø 4,4 mm (0.17 in.)
34,0 mm (1.34 in.)
CMPT2310
ACCEL signal / supply WHITE
S/N 00000 ACCEL/TEMP GND (common) BLACK
21,0 mm (0.83 in.)
TEMP signal high
RED (CMPT 2310T only)
GND wire
Sensor – Temperature (SKF CMPT 2310T)
• Sensitivity: 10 mV/°C
• Temperature sensor measurement range: 0 to 120 °C (30 to +250 °F)
• Precision: ±1,5 °C (±2.7 °F)
Wire connections – SKF CMPT 2310T
Electrical
• • • •
Power requirements
Environmental
• Voltage source: 24 V DC nominal, 18 to 30 V DC
• Constant current diode: 4 mA DC at 24 V, 2 to 10 mA is permissible.
• Acceleration sensor bias voltage: 11,5 V DC, ±10% for 24 V DC supply at 25 °C (+75 °F)
• Over voltage protection: Approximately 18 V DC
• Reverse polarity (wiring) protection installed
• Cable: Integral cable, 5 m (16.4 ft.) length
• Acceleration sensor electrical noise level: < 1 mg RMS broadband 2,5 Hz to 25,0 kHz
• Wire specification: 0,32 mm² (AWG 22) stranded tin copper (seven strands at 0,05 mm² each)
• Grounding/Shielding: Case isolated, internal shielding (Faraday cage), Faraday cage connected to power supply return
• • • • •
Wire connections – SKF CMPT 2310
• White: ACCEL signal/power (connected to constant current source)
• Black: ACCEL signal ground (GND)
• Blank twisted wire: Screen connected to internal shield
White: ACCEL signal/power Black: ACCEL/TEMP signal ground (GND) Red: TEMP signal high
Blank twisted wire: Screen connected to internal shield
Maximum operating temperature: 120 °C (250 °F) Storage temperature: –50 to +150 °C (–60 to +300 °F)
Vibrations limits: 70 g peak Shock limit: 5 000 g peak Electromagnetic sensitivity, equivalent g, maximum:
< 100 μg/Gauss at 50 to 60 Hz
• CE: According to the generic immunity standard for Industrial Environment EN 50082-2
• IEC: 529, IP 67 Physical
• Weight:
– Sensor without cable: 210 g (7.4 oz.)
– Sensor with cable: 410 g (14.5 oz.)
• Sensor housing material: 304 stainless steel
• Hardware: One M6 × 1 socket head cap screw (30 mm long) and one 1/4-28 UNF socket head cap screw (1.25 in. long) included
• Screw torque: 6 Nm (50 in. lbs.)
Please contact:
SKF Condition Monitoring Center – Luleå Aurorum 30, SE-977 75 · Luleå, Sweden
Tel: +46 (0)31 337 1000 · Fax: +46 (0)920 134 40 Web: www.skf.com/cm ® SKF is a registered trademark of the SKF Group.
All other trademarks are the property of their respective owners.
© SKF Group 2012 The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be
accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.
PUB CM/P8 12817 EN · April 2012
skf.com