im-tek.com

Dynisco ECHO-MV3-BAR-R21-UNF-6PN-S06-F18-NTR Melt Pressure Transducers

Dynisco

Product Code: ECHO-MV3-BAR-R21-UNF-6PN-S06-F18-NTR Melt Pressure Transducers
Brand: Dynisco



GET OFFER: info@imtek.com.tr

Description for Dynisco ECHO-MV3-BAR-R21-UNF-6PN-S06-F18-NTR Melt Pressure Transducers

·         2 year warranty and 60 years of Dynisco industry experience·         Accuracy better than ±0.5%·         TiAlN diaphragm coating is standard·         mV/V, 0-10VDC, or mA outputs available·         Integral temperature sensor option·         Available in configurations that fit most extruder applications·         1.5M, 3M, 5M, 7.5M & 10M psi pressure range capability·         Alternative fill model available  Operating Principle The Dynisco EchoTM Melt Pressure Sensors are used to make pressure measurements of molten polymers up to 752°F (400°C). These models incorporate a 350?Ohm, bonded foil strain gage Wheatstone Bridge. This proven technology provides an output of 0?3.33 mV/V, & 4?20mA, 05?VDC and 0?10VDC proportional to melt pressure (within the specified error band). Most models include an internal shunt calibration ("Rcal") function that is used to simulate a signal of 80% of full scale. This eliminates the need for a cumbersome calibrated pressure source when scaling associated instrumentation. Installation Do not remove protective cap until ready to install. Prior to initial installation, verify correct machining of mounting hole per Figure 1. Gauge Plug, P/N 200908, is available for this purpose. Before installing make sure that mounting hole is clear of material. Dynisco Cleaning Tool Kit, P/N 200100, should be used. To prevent galling, lightly coat transducer threads with a high temperature anti?seize material. An adequate seal, in a properly machined and maintained mounting well, is obtained with 100 in?lbs. mounting torque. The maximum torque recommended is 500 in?lbs. The electronics housing should be secured, with the optional mounting bracket (P/N 200941), in an area where the ambient temperature will not exceed 185°F (85°C). (Mounting bracket not supplied with EchoTM models.)Wiring Use shielded cable. Attach cable shield to ground at one end only. NOTE: DYNISCO cable assemblies are constructed with shield wired to transducer mating connector, so do not attach shield to instrument. Output Supply Voltage mV/V 10 Vdc (12 Vdc max) mA 14?36 Vdc Vdc 16?36 Vdc Start?Up Bring system to operating temperature with no pressure. For mA units, remove adjustment access screw and adjust Zero Output potentiometer. For mV/V units, zero adjustment must be handled by downstream indicator. Make sure that there is sufficient "soak time" to assure that any material at the tip of the transducer is molten before extruder drive is started. Removal Transducer should only be removed when polymer is hot and liquid. Wipe tip with a soft cloth immediately. The melt pressure transducer must be removed before using an abrasive material or wire brush to clean the extruder barrel. Clean the mounting well before attempting to reinstall the transducer with Dynisco Mounting Well Cleaning Tool Kit, P/N 200100. Thermocouple Thermocouples ( Type J or K) in a rigid stem are optionally available. The Type J (iron?constantan) and Type K is a T/C junction just behind the flush diaphragm at the tip of the transducer. For the most accurate temperature measurement of the melt stream, use a separate immersion?type thermocouple, such as Dynisco TB422 fixed depth series or (G)RMT adjustable models. The thermocouple assembly can be removed by loosening the set screw on the side of hex assembly and pulling the T/C probe, carefully, straight out, without twisting. Replacement assemblies are available. When installing the thermocouple probe assembly, align the slot with the pressure capillary tube and press into snout until top of probe shoulders flush against snout. Lock in place with set screw.Warranty This Dynisco product is warranted under terms and conditions set forth in the Dynisco Web Pages. Go to www.dynisco.com and click on “Warranty” at the bottom of any page for complete details.

Recommended Products For Dynisco


Dynisco TDT432F-A-1-2-5C-32/46-S137 Pressure Sensors
Dynisco PT412-5M 9/18-B784 Pressure Sensors
Dynisco PT4624-1/2-5M-6/18-SIL2 Pressure Sensors
Dynisco SPX4622-S-A-00-B-21-DP-DD-A-AA-ZZ Pressure Sensors
Dynisco TPT4634-2CB-6/18-S137A Pressure Sensors
Dynisco TPT432A-3M-6/18 Pressure Sensors
Dynisco 2291SA48P21BUMMACAAA Pressure Sensors
Dynisco MDT462F-1/2-2C-15/46-A Melt Pressure Transmitters
Dynisco PT-242FM-20MPA-6 Pressure Sensors
Dynisco MDT462F-1/2-3,5C-15/91-SIL2 Melt Pressure Transmitters
Dynisco PT4624-5M-6/18-SIL2 Pressure Sensors
Dynisco 4622NA00P24CEDDAAFZZGC7 Pressure Sensor
Dynisco DYMT-S-1/2-RTD-15-15-G Melt Temperature Probe
Dynisco UPR90030000000 Process Indicator
Dynisco DYMT-S-M18-J-7-15-G-2M-F13 Melt Temperature Probe
Dynisco 2291NA48K13BUMMACAZZ Pressure Sensors
Dynisco SPX4222-S-A-00-B-13-EZ-DD-C-AA-ZZ-Z017 Pressure Sensors
Dynisco 224200001317 Pressure Sensors
Tellarini ENM 20 L 500 L Electric Pump
Ru-Steel RP 700 RP 6 Bolt Range Without Spacer
PTM HPA 3000 Hydraulic-Pneumatic Rotary Actuators
Adalet CSC4X6-050506 (1x1 w/ Terminal Blocks) CSC Series Pushbutton Station Enclosures
Vulcanic 2281-83 Flange Immersion Heater
Vulcanic 2116-15 Screw Plug Immersion Heater
Grundfos NK 100-180/146 AA1F1S3ESBQQEHW3 Pump
MBS MLD 168 19 20 1 2000 Mixflo Multitube Demontable Heat Exchanger
Ifm E20940 Mounting rod
Faulhaber AM1524SB015055 Stepper Motor
Eaton DGMC3-BT-CWB-41 B Line Relief Valve
American Industrial URCN-1284 Heat Exchanger
Romano RO-M22 Position Transmitter
Stenflex Type SF-10 DN 2000 Expansion Joint
Parker 15P210QBPKS124 Duplex Filter
Fimet M225M2 8M1700 45 KW Motor
HFB GUF 220 Plummer Block Housing
JVM JX 104-50 Unbalance Motor
Bollfilter 5404237
Alfa Laval 9613361127 UNIQUE SSV TO 63.5/2½ INCH 002 W 0.8/BLASTED EPDM SHUT OFF TANK OUTLET NC
BELIMO H6015X4-S2 Valve
Eurotherm RCT48 Emperature Control Relay Eurotherm RCT48 Emperature Control Relay
Fisher V200 Control Valve
Grundfos NK 125-225/179 AA1F1S3ESBQQELW3 Pump