Pièces détachées industrielles & solutions d'ingénierie depuis 2001.
- Produits
- Ropex
- Contrôleur
- Ropex UPT-6011 Temperature Controller
Ropex UPT-6011 Temperature Controller
Fiches Techniques / Documentation Produit
| Marque |  |
| Catégorie | Contrôleur |
| Nom du produit | Ropex UPT-6011 Temperature Controller |
| Code produit | Non spécifié |
Contactez-nous ! Nous revenons vers vous sous 24 heures ouvrées (hors week-ends et jours fériés) pour confirmer la disponibilité et le délai estimé.
Description du produit
Les produits Ropex, dont Ropex UPT-6011 Temperature Controller, sont sourcés via des canaux d'importation parallèle et livrés à nos clients en United States rapidement et en toute fiabilité. Imtek Engineering propose des pièces Ropex authentiques à des prix compétitifs. Même si Ropex UPT-6011 Temperature Controller n'est pas répertorié sur notre site, vous pouvez demander un devis — notre équipe vous répondra rapidement.
United States2. Mount the CIRUS® Temperature Controller on a standard top hat rail (TS35 rail according to DIN EN 50022) in
the electrical cabinet. If several controllers are mounted on one rail, the minimum clearance specified in
section 10 "Technical data" on page 73 must be allowed between them.
3. Wire the system in accordance with the instructions in section 6.1 "Installation notes" on page 10, section 6.6
"Wiring diagram (standard)" on page 15, and the ROPEX Application Report. The information provided in
section 6.1 "Installation notes" on page 10 must also be observed.
Wires used for control or measuring connections must always be laid inside the building.
4. An overcurrent protective device with a maximum rating of 10 A must be fitted when the device is installed, e.g.:
- Miniature circuit breaker to EN 60898 (B, C, D, K, or Z characteristic)
- Miniature circuit breaker to UL 489 (*) (B, C, D, K, or Z characteristic)
- Fuse gG to IEC 60269
- Class CC or Class J fuse to UL 248 (*) The overcurrent protective devices marked (*) should be used in installations conforming to UL standards.
If one such device is not adequate for the heatsealing application, two separate overcurrent protective devices
should be provided – one for the controller and one for the application ( ROPEX Application Report).
The overcurrent protective device must be located directly adjacent to the controller.
The minimum possible specification for this device is indicated in the ROPEX Application Report based on the
calculated currents. If a larger overcurrent protective device is fitted, you must match the current carrying
capacity of the other components accordingly (e.g. cables, impulse transformer etc.).
5. A disconnecting device must be provided when the system is installed; it must be marked as belonging to the
system and fitted in a readily accessible position.
If a miniature circuit breaker is used, it can also perform the function of this device.
6. Connect the CIRUS temperature controller to the EtherNet/IPTM scanner using a suitable (standard compliant)
cable.
!
Check that all system connections – including the terminals for the impulse transformer windings
– are securely attached.
7. Make sure the wiring conforms to all relevant national and international installation regulations.
Page 11
UPT-6011
Version 5
Questions Fréquentes
Questions fréquemment posées sur Ropex UPT-6011 Temperature Controller de Ropex. Imtek Engineering est prêt à vous aider à vous procurer Ropex UPT-6011 Temperature Controller de Ropex en United States.
Imtek Engineering s'approvisionne en produits Ropex authentiques via des canaux d'approvisionnement fiables et les propose aux clients en United States à des prix compétitifs.
