Pièces détachées industrielles & solutions d'ingénierie depuis 2001.
Solberg 274P Filter Insert Paper With Pre-filter Sleeve
Fiches Techniques / Documentation Produit
| Marque | |
| Catégorie | Filtre |
| Nom du produit | Solberg 274P Filter Insert Paper With Pre-filter Sleeve |
| Code produit | 274P |
Contactez-nous ! Nous revenons vers vous sous 24 heures ouvrées (hors week-ends et jours fériés) pour confirmer la disponibilité et le délai estimé.
Description du produit
Les produits Solberg, dont Solberg 274P Filter Insert Paper With Pre-filter Sleeve, sont sourcés via des canaux d'importation parallèle et livrés à nos clients en United States rapidement et en toute fiabilité. Imtek Engineering propose des pièces Solberg authentiques à des prix compétitifs. Même si Solberg 274P Filter Insert Paper With Pre-filter Sleeve n'est pas répertorié sur notre site, vous pouvez demander un devis — notre équipe vous répondra rapidement.
the element. As the element fills up with dirt, the pressure drop increases. It is
important to document the pressure drop across a given filter when it is new and
then clean or replace it when the pressure drop increases by 10” to 15” / 250280mm H2O over the original reading.
Rule of Thumb #5: The inlet connection greatly influences the overall pressure
drop of the filter system. To minimize the restriction contributed by an inlet filter, a
velocity of 6,000 ft/min (10200m3/h) or less is suggested through the outlet pipe.
The table below lists the suggested flows based on pipe size:
Pipe Size (inches)
Max Airflow
Pipe Size (inches)
Max Airflow
1/2"
10 CFM
17m3/h
4"
520 CFM
884m3/h
3/4"
20 CFM
34m3/h
5"
800 CFM
1360m3/h
1"
35 CFM
60m3/h
6"
1,100 CFM
1870m3/h
1 ¼"
60 CFM 102m3/h
8"
1,800 CFM
3060m3/h
1 ½"
80 CFM 136m3/h
10"
3,300 CFM
5610m3/h
2"
135 CFM 230m3/h
12"
4,700 CFM
7990m3/h
2 ½"
195 CFM 332m3/h
14"
6,000 CFM 10200m3/h
3"
300 CFM 510m3/h
Table 3 *Note: This information is for general use only. A qualified engineer must properly design each system.
3. Element Specifications Temperature Range: -15° to 220°F / -26° to 105°C
Filter Change-Out Differential: 10” to 15” / 250-380mm H2O Over Initial Delta P
Media Micron Rating Standard Paper 99+% @ 2 micron Standard Polyester 99+% @ 5 micron
“S” Series Wire Mesh Epoxy Coated Wire Mesh “Z” Series Polyester 99+% @ 1 micron
“HE” Series HEPA 99.97% @ 0.3 microns “U” Series Polyester 99+% @ 25 micron
“W” Series Polyester 99+% @ 100 micron “S2” Series Stainless Steel Wire Mesh
“AC” & “ACP” Series N/A “Y” Series Polypropylene 99+% @ 10 micron Table 4
Temperature Range: -15° to 385°F / -26° to 196°C Filter Change-Out Differential: 10” to 15”/ 250-380mm H2O Over Initial Delta P
Media Micron Rating “MX” & “MXD” Series – Nomex Cloth 99+% @ 10 micron Table 5
Page 6 Solberg Manufacturing, Inc., 1151 Ardmore Itasca, IL 60143 USA Ph: 630.773.1363 Fax: 630.773.0727 Email: [email protected] Web: www.solbergmfg.com
Questions Fréquentes
Questions fréquemment posées sur Solberg 274P Filter Insert Paper With Pre-filter Sleeve de Solberg. Imtek Engineering est prêt à vous aider à vous procurer Solberg 274P Filter Insert Paper With Pre-filter Sleeve de Solberg en United States.
Imtek Engineering s'approvisionne en produits Solberg authentiques via des canaux d'approvisionnement fiables et les propose aux clients en United States à des prix compétitifs.

