2001년부터 산업용 부품 및 엔지니어링 솔루션.
독일에서 전 세계로 빠른 배송
다양한 결제 방법다양한 결제 옵션
- 제품
- B&R Automation
- 모듈
- B&R Automation X20DO8332 Module
B&R Automation X20DO8332 Module
기술 데이터시트 / 제품 문서
| 브랜드 | |
| 카테고리 | 모듈 |
| 제품명 | B&R Automation X20DO8332 Module |
| 제품 코드 | X20DO8332 |
저희에게 연락하세요! 영업일 기준 24시간 이내(주말 및 공휴일 제외) 재고 상태와 예상 납기를 안내해 드립니다.
제품 설명
B&R Automation의 B&R Automation X20DO8332 Module을(를) 포함한 제품은 병행 수입 채널을 통해 조달되며 United States의 고객에게 신속하고 안정적으로 배송됩니다. Imtek Engineering은 경쟁력 있는 가격으로 정품 B&R Automation 부품을 제공합니다. B&R Automation X20DO8332 Module이 당사 웹사이트에 등록되어 있지 않더라도 언제든지 견적을 요청하실 수 있으며, 담당 팀이 신속히 답변 드릴 것입니다.
United StatesTechnical description Order number Switching delay 0→1 1→0 Switching frequency
Resistive load Inductive load Braking voltage when switching off inductive
loads Insulation voltage between channel and bus Additional functions Electrical properties
Electrical isolation Operating conditions Mounting orientation Horizontal
Vertical Installation elevation above sea level 0 to 2000 m >2000 m Degree of protection per EN 60529
Ambient conditions Temperature Operation Horizontal mounting orientation
Vertical mounting orientation Derating Starting temperature Storage Transport
Relative humidity Operation Storage Transport Mechanical properties Note
X20DO8332
X20cDO8332 <300 µs <300 µs
Max. 500 Hz See section "Switching inductive loads".
Typ. 50 VDC 500 Veff Outputs can be connected in parallel to increase the output current.
Channel isolated from bus and I/O power supply
Yes Yes No limitation Reduction of ambient temperature by 0.5°C per 100 m
IP20
-25 to 60°C -25 to 50°C See section "Derating".
-
Yes, -40°C -40 to 85°C -40 to 85°C
5 to 95%, non-condensing Up to 100%, condensing 5 to 95%, non-condensing
5 to 95%, non-condensing Order 1x terminal block X20TB12 separately.
Order 1x terminal block X20TB12 separately.
Order 1x bus module X20BM11 separately.
Order 1x bus module X20cBM11 separately.
12.5+0.2 mm
Pitch
Table 2: X20DO8332, X20cDO8332 - Technical data 1) 2)
Number of outputs x RDS(on) x Nominal output current2. For a calculation example, see section "Mechanical and electrical configuration" in the X20
system user's manual.
Derating must be observed for summation current starting at 6 A.
2.2 Status LEDs For a description of the various operating modes, see section "Additional information - Diagnostic LEDs"
in the X20 system user's manual.
Figure
6
LED r
Color Green
Status Off Single flash Blinking On Off Single flash
e
Red
e+r 1-8
Double flash Red on / Green single flash Orange
Description Module supply not connected
RESET mode
PREOPERATIONAL mode
RUN mode Module supply not connected or everything OK Warning/Error on an I/O channel. Level monitoring for digital outputs has
been triggered.
I/O supply too low Invalid firmware Output status of the corresponding digital output
X20(c)DO8332 Data sheet V 3.31
Resistive load Inductive load Braking voltage when switching off inductive
loads Insulation voltage between channel and bus Additional functions Electrical properties
Electrical isolation Operating conditions Mounting orientation Horizontal
Vertical Installation elevation above sea level 0 to 2000 m >2000 m Degree of protection per EN 60529
Ambient conditions Temperature Operation Horizontal mounting orientation
Vertical mounting orientation Derating Starting temperature Storage Transport
Relative humidity Operation Storage Transport Mechanical properties Note
X20DO8332
X20cDO8332 <300 µs <300 µs
Max. 500 Hz See section "Switching inductive loads".
Typ. 50 VDC 500 Veff Outputs can be connected in parallel to increase the output current.
Channel isolated from bus and I/O power supply
Yes Yes No limitation Reduction of ambient temperature by 0.5°C per 100 m
IP20
-25 to 60°C -25 to 50°C See section "Derating".
-
Yes, -40°C -40 to 85°C -40 to 85°C
5 to 95%, non-condensing Up to 100%, condensing 5 to 95%, non-condensing
5 to 95%, non-condensing Order 1x terminal block X20TB12 separately.
Order 1x terminal block X20TB12 separately.
Order 1x bus module X20BM11 separately.
Order 1x bus module X20cBM11 separately.
12.5+0.2 mm
Pitch
Table 2: X20DO8332, X20cDO8332 - Technical data 1) 2)
Number of outputs x RDS(on) x Nominal output current2. For a calculation example, see section "Mechanical and electrical configuration" in the X20
system user's manual.
Derating must be observed for summation current starting at 6 A.
2.2 Status LEDs For a description of the various operating modes, see section "Additional information - Diagnostic LEDs"
in the X20 system user's manual.
Figure
6
LED r
Color Green
Status Off Single flash Blinking On Off Single flash
e
Red
e+r 1-8
Double flash Red on / Green single flash Orange
Description Module supply not connected
RESET mode
PREOPERATIONAL mode
RUN mode Module supply not connected or everything OK Warning/Error on an I/O channel. Level monitoring for digital outputs has
been triggered.
I/O supply too low Invalid firmware Output status of the corresponding digital output
X20(c)DO8332 Data sheet V 3.31
자주 묻는 질문
B&R Automation의 B&R Automation X20DO8332 Module에 관한 자주 묻는 질문입니다. Imtek Engineering은 United States에서 B&R Automation의 B&R Automation X20DO8332 Module를 조달하는 데 도움을 드릴 준비가 되어 있습니다.
Imtek Engineering은 신뢰할 수 있는 공급 채널을 통해 정품 B&R Automation 제품을 조달하여 United States 고객에게 경쟁력 있는 가격으로 제공합니다.
