Eurotherm TE10S Solid State Relay

CE marking TE10S Units are CE marked to show that they meet the essential
requirements of the European Low Voltage Directive. No exposed parts are at a dangerous voltage.
Eurotherm certificates that the TE10S units have successfully passed the EMC tests and enable the system which incorporates them to
comply with the EMC Directive as far as the TE10S is concerned.
An EMC installation guide (part no. HA025464) is available on request.
SPECIFICATION Current:
16A, 25A, 40A and 50A at 45°C. Under certain conditions e.g. lower ambient temperature
these units may be run at slightly higher currents. Consult your local Eurotherm
engineer
Voltage:
48 to 240 Vac (+10%, -15%) or 96 to 500 Vac (+10%, -15%)
Supply frequency:
47 to 63 Hz
Environmental Humidity:
IP20 (IEC 529)
Isolation:
All distances comply with IEC 644 Control signals isolated from power, tested to
3600Vac. Isolation to earth tested to 2000Vac
Electrical protection:
Load Load type:
Constant resistance or shortwave infrared elements
Single phase connection:
Three phase connection:
Line-to-line or line-to-neutral Three wire star or delta - two units control two
limbs of the load Four wire star with neutral or six wire open delta - three units together
Firing mode:
Logic firing (ON/OFF) with zero voltage switching
Leakage current:
Less than 30mA
Storage temperature:
-10°C to 70°C
Cooling:
Natural convection
Operating temperature:
0°C to 45°C (up to 60° with derating)
Safety standards:
EN61010, installation category 3 (voltage transients must not exceed 4.0KV)
Atmospheres:
Electrically conductive pollution must be excluded from the cabinet in which this
controller is mounted. This product is not suitable for use above 2000m or in corrosive or
explosive atmospheres without further protection
Polarity insensitive + and - can be crossed Command signal indication by green LED
LGC 8 to 32Vdc (ON>8V, OFF<2V)
LAC 32 to 48Vac, (ON>30V, OFF<5V)
HAC 100 to 240Vac (ON>85V, OFF<10V) Current:
LGC 9mA dc (self limiting). (ON>9mA, OFF<0.5mA)
European directives Electromagnetic compatibility Immunity test standards: EN61000-4, EN61000-4-4, PrEN 61000-4-3
Emission test standard: EN55011, EN50081-2 without external filter (optional parallel filters must be fitted for 2
phase control pf 3 phase loads)
Option Partial load failure detection:
Detects an increase in load impedance due to failure or disconnection of part of the heating
load
Safety:
Complies with Low Directive 73/23/EEC dated 19/2/73 amended by Directive 93/68/EEC dated
22/7/93 (product installed and used in compliance with its user manual)
CE marking:
TE10S products carry the CE mark in compliance with the European Low Voltage
Directive. A CE declaration of conformity is available on request
Discrimination: 1 element in 6 for single phase load Installation Dimensions (mm):
Mounting:
Inter-unit spacing:
Internal bus bar:
Power terminals:
Control terminals:
Weight:
16A 115H x 35W x 93D (53W with PLF/IPF);
25A 115H x 53W x 93D (70W with PLF/IPF);
40A 115H x 88W x 93D (105W with PLF/IPF);
50A 115H x 105W x 93D (123W with PLF/IPF) Vertical on DIN rail 10mm for full current operation
8mm2 copper bars Cable sizes 1.5 to 16mm2. Tightening torque 1.2Nm Cable size 0.5 to 1.5mm2. Terminals are
removable for easy maintenance 16A 320g, 25A 500g, 40A 770g, 50A 880g
RC snubber network External high speed fuse (to be ordered separately)
Input
Voltage:
5 to 95% non condensing
Enclosure protection: