2001년부터 산업용 부품 및 엔지니어링 솔루션.
독일에서 전 세계로 빠른 배송
다양한 결제 방법다양한 결제 옵션
MOOG E124-204-400
기술 데이터시트 / 제품 문서
| 브랜드 |  |
| 카테고리 | 기타 |
| 제품명 | MOOG E124-204-400 |
| 제품 코드 | 미지정 |
저희에게 연락하세요! 영업일 기준 24시간 이내(주말 및 공휴일 제외) 재고 상태와 예상 납기를 안내해 드립니다.
제품 설명
MOOG의 MOOG E124-204-400을(를) 포함한 제품은 병행 수입 채널을 통해 조달되며 United States의 고객에게 신속하고 안정적으로 배송됩니다. Imtek Engineering은 경쟁력 있는 가격으로 정품 MOOG 부품을 제공합니다. MOOG E124-204-400이 당사 웹사이트에 등록되어 있지 않더라도 언제든지 견적을 요청하실 수 있으며, 담당 팀이 신속히 답변 드릴 것입니다.
United StatesSPECIFICATIONS Electrical Stroke:
From 2 inches to 100 inches
Ripple:
Less than 0.8% of full output
Zero Output:
Either end of transducer (factory set)
Output Voltage:
0 to +10 VDC (bipolar also available)
Zero Adjustment:
Nominal 2% of full stroke
Special Output:
Pulse width modulated output (0 V to +12 V)
Linearity:
Less than ±0.05% of full stroke
Temperature Range:
0°C (32°F) to 50°C (122°F)
Repeatability:
Better than ±0.02% of full stroke
Connector:
DIN 41612 C
Temperature Coefficient:
0.013% per degree C
Form Factor:
Eurocard 100 x 160 mm, 7 HP, 3 U
Frequency Response:
Typical 400 Hz for 20 inch stroke
Weight:
0.38 lb (0.17 kg)
NE124-204 Series Temposonics™ Signal Conditioner
The Temposonics™ Signal Conditioner card is designed to provide the necessary power supplies and signal conditioning to drive a range of
Temposonics™ transducers.The card is factory set to drive a specific stroke
length.Trimpots, which adjust zero and gain, are used to compensate for minor
differences between transducers of the same nominal stroke length.Transducer
position is represented by an analog voltage.The inverse of this voltage and a
pulse width modulated signal are also available.
The NE124-204 Temposonics™ Signal Conditioner card is a forward compatible replacement for the E124-204.
FEATURES ➢ ➢ ➢ ➢ ➢ ➢ ➢
Analog output Infinite resolution Absolute measurement Zero adjustment Gain control
±15 VDC supplies
PWM output
ADJUSTMENTS Zero (R17) – Adjusts null of outputs for zero transducer conditions. Used
for ‘fine’ tuning the DC analog output at full retract and full extend positions.
(Factory set – front panel access)
ORDER NUMBER NE124-204-x (consult factory)
FUNCTION SELECTION J1 Analog Output Jumper: Select ‘on’ for DC analog output at Pin-25
and Pin-32. Select ‘off’ for DC analog output on Pin-25 only. (Factory set for
Pin-25.) J2 Inverse Analog Output Jumper: Select ‘on’ for inverse analog output
at Pin-27 and Pin-31. Select ‘off’ for inverse analog output on Pin-27 only.
(Factory set for Pin-27.)
Gain (R34) – Adjusts gain to the exact output option change for a zero to
full displacement magnet movement. . Used for ‘fine’ tuning the DC analog
output at full retract and full extend positions. (Factory set – PCB mtg. only –
not accessible on front panel)
From 2 inches to 100 inches
Ripple:
Less than 0.8% of full output
Zero Output:
Either end of transducer (factory set)
Output Voltage:
0 to +10 VDC (bipolar also available)
Zero Adjustment:
Nominal 2% of full stroke
Special Output:
Pulse width modulated output (0 V to +12 V)
Linearity:
Less than ±0.05% of full stroke
Temperature Range:
0°C (32°F) to 50°C (122°F)
Repeatability:
Better than ±0.02% of full stroke
Connector:
DIN 41612 C
Temperature Coefficient:
0.013% per degree C
Form Factor:
Eurocard 100 x 160 mm, 7 HP, 3 U
Frequency Response:
Typical 400 Hz for 20 inch stroke
Weight:
0.38 lb (0.17 kg)
NE124-204 Series Temposonics™ Signal Conditioner
The Temposonics™ Signal Conditioner card is designed to provide the necessary power supplies and signal conditioning to drive a range of
Temposonics™ transducers.The card is factory set to drive a specific stroke
length.Trimpots, which adjust zero and gain, are used to compensate for minor
differences between transducers of the same nominal stroke length.Transducer
position is represented by an analog voltage.The inverse of this voltage and a
pulse width modulated signal are also available.
The NE124-204 Temposonics™ Signal Conditioner card is a forward compatible replacement for the E124-204.
FEATURES ➢ ➢ ➢ ➢ ➢ ➢ ➢
Analog output Infinite resolution Absolute measurement Zero adjustment Gain control
±15 VDC supplies
PWM output
ADJUSTMENTS Zero (R17) – Adjusts null of outputs for zero transducer conditions. Used
for ‘fine’ tuning the DC analog output at full retract and full extend positions.
(Factory set – front panel access)
ORDER NUMBER NE124-204-x (consult factory)
FUNCTION SELECTION J1 Analog Output Jumper: Select ‘on’ for DC analog output at Pin-25
and Pin-32. Select ‘off’ for DC analog output on Pin-25 only. (Factory set for
Pin-25.) J2 Inverse Analog Output Jumper: Select ‘on’ for inverse analog output
at Pin-27 and Pin-31. Select ‘off’ for inverse analog output on Pin-27 only.
(Factory set for Pin-27.)
Gain (R34) – Adjusts gain to the exact output option change for a zero to
full displacement magnet movement. . Used for ‘fine’ tuning the DC analog
output at full retract and full extend positions. (Factory set – PCB mtg. only –
not accessible on front panel)
자주 묻는 질문
MOOG의 MOOG E124-204-400에 관한 자주 묻는 질문입니다. Imtek Engineering은 United States에서 MOOG의 MOOG E124-204-400를 조달하는 데 도움을 드릴 준비가 되어 있습니다.
Imtek Engineering은 신뢰할 수 있는 공급 채널을 통해 정품 MOOG 제품을 조달하여 United States 고객에게 경쟁력 있는 가격으로 제공합니다.
