2001년부터 산업용 부품 및 엔지니어링 솔루션.
독일에서 전 세계로 빠른 배송
다양한 결제 방법다양한 결제 옵션
Solberg 9240825 O-ring
기술 데이터시트 / 제품 문서
| 브랜드 |  |
| 카테고리 | 기타 |
| 제품명 | Solberg 9240825 O-ring |
| 제품 코드 | 9240825 |
저희에게 연락하세요! 영업일 기준 24시간 이내(주말 및 공휴일 제외) 재고 상태와 예상 납기를 안내해 드립니다.
제품 설명
Solberg의 Solberg 9240825 O-ring을(를) 포함한 제품은 병행 수입 채널을 통해 조달되며 United States의 고객에게 신속하고 안정적으로 배송됩니다. Imtek Engineering은 경쟁력 있는 가격으로 정품 Solberg 부품을 제공합니다. Solberg 9240825 O-ring이 당사 웹사이트에 등록되어 있지 않더라도 언제든지 견적을 요청하실 수 있으며, 담당 팀이 신속히 답변 드릴 것입니다.
United StatesRule of Thumb #4: Pressure drop is also caused by the dirt holding capacity of
the element. As the element fills up with dirt, the pressure drop increases. It is
important to document the pressure drop across a given filter when it is new and
then clean or replace it when the pressure drop increases by 10” to 15” / 250280mm H2O over the original reading.
Rule of Thumb #5: The inlet connection greatly influences the overall pressure
drop of the filter system. To minimize the restriction contributed by an inlet filter, a
velocity of 6,000 ft/min (10200m3/h) or less is suggested through the outlet pipe.
The table below lists the suggested flows based on pipe size:
Pipe Size (inches)
Max Airflow
Pipe Size (inches)
Max Airflow
1/2"
10 CFM
17m3/h
2 ½"
195 CFM
332m3/h
3/4"
20 CFM
34m3/h
3"
300 CFM
510m3/h
1"
35 CFM
60m3/h
4"
520 CFM
884m3/h
1 ¼"
60 CFM 102m3/h
5"
800 CFM
1360m3/h
1 ½"
80 CFM 136m3/h
6"
1,100 CFM
1870m3/h
2"
135 CFM 230m3/h
Table 3 *Note: This information is for general use only. A qualified engineer must properly design each system.
3. Element Specifications Temperature Range: -15° to 220°F / -26° to 105°C
Filter Change-Out Differential: 10” to 15” / 250-380mm H2O Over Initial Delta P
Media Micron Rating Standard Paper 99+% @ 2 micron Standard Polyester 99+% @ 5 micron
“S” Series Wire Mesh Epoxy Coated Wire Mesh “Z” Series Polyester 99+% @ 1 micron
“HE” Series HEPA 99.97% @ 0.3 microns “U” Series Polyester 99+% @ 25 micron
“W” Series Polyester 99+% @ 100 micron “S2” Series Stainless Steel Wire Mesh
“AC” & “ACP” Series N/A “Y” Series Polypropylene 99+% @ 10 micron
Table 4
Temperature Range: -15° to 385°F / -26° to 196°C Filter Change-Out Differential: 10” to 15”/ 250-380mm H2O Over Initial Delta P
Media Micron Rating “MX” & “MXD” Series – Nomex Cloth 99+% @ 10 micron
Table 5
Page 6 Solberg Manufacturing, Inc., 1151 Ardmore Itasca, IL 60143 USA Ph: 630.773.1363 Fax: 630.773.0727 Email: [email protected] Web: www.solbergmfg.com
the element. As the element fills up with dirt, the pressure drop increases. It is
important to document the pressure drop across a given filter when it is new and
then clean or replace it when the pressure drop increases by 10” to 15” / 250280mm H2O over the original reading.
Rule of Thumb #5: The inlet connection greatly influences the overall pressure
drop of the filter system. To minimize the restriction contributed by an inlet filter, a
velocity of 6,000 ft/min (10200m3/h) or less is suggested through the outlet pipe.
The table below lists the suggested flows based on pipe size:
Pipe Size (inches)
Max Airflow
Pipe Size (inches)
Max Airflow
1/2"
10 CFM
17m3/h
2 ½"
195 CFM
332m3/h
3/4"
20 CFM
34m3/h
3"
300 CFM
510m3/h
1"
35 CFM
60m3/h
4"
520 CFM
884m3/h
1 ¼"
60 CFM 102m3/h
5"
800 CFM
1360m3/h
1 ½"
80 CFM 136m3/h
6"
1,100 CFM
1870m3/h
2"
135 CFM 230m3/h
Table 3 *Note: This information is for general use only. A qualified engineer must properly design each system.
3. Element Specifications Temperature Range: -15° to 220°F / -26° to 105°C
Filter Change-Out Differential: 10” to 15” / 250-380mm H2O Over Initial Delta P
Media Micron Rating Standard Paper 99+% @ 2 micron Standard Polyester 99+% @ 5 micron
“S” Series Wire Mesh Epoxy Coated Wire Mesh “Z” Series Polyester 99+% @ 1 micron
“HE” Series HEPA 99.97% @ 0.3 microns “U” Series Polyester 99+% @ 25 micron
“W” Series Polyester 99+% @ 100 micron “S2” Series Stainless Steel Wire Mesh
“AC” & “ACP” Series N/A “Y” Series Polypropylene 99+% @ 10 micron
Table 4
Temperature Range: -15° to 385°F / -26° to 196°C Filter Change-Out Differential: 10” to 15”/ 250-380mm H2O Over Initial Delta P
Media Micron Rating “MX” & “MXD” Series – Nomex Cloth 99+% @ 10 micron
Table 5
Page 6 Solberg Manufacturing, Inc., 1151 Ardmore Itasca, IL 60143 USA Ph: 630.773.1363 Fax: 630.773.0727 Email: [email protected] Web: www.solbergmfg.com
자주 묻는 질문
Solberg의 Solberg 9240825 O-ring에 관한 자주 묻는 질문입니다. Imtek Engineering은 United States에서 Solberg의 Solberg 9240825 O-ring를 조달하는 데 도움을 드릴 준비가 되어 있습니다.
Imtek Engineering은 신뢰할 수 있는 공급 채널을 통해 정품 Solberg 제품을 조달하여 United States 고객에게 경쟁력 있는 가격으로 제공합니다.
