2001년부터 산업용 부품 및 엔지니어링 솔루션.
독일에서 전 세계로 빠른 배송
다양한 결제 방법다양한 결제 옵션
Valco FCM Flow Switch
기술 데이터시트 / 제품 문서
| 브랜드 |  |
| 카테고리 | 스위치 |
| 제품명 | Valco FCM Flow Switch |
| 제품 코드 | 미지정 |
저희에게 연락하세요! 영업일 기준 24시간 이내(주말 및 공휴일 제외) 재고 상태와 예상 납기를 안내해 드립니다.
제품 설명
Valco의 Valco FCM Flow Switch을(를) 포함한 제품은 병행 수입 채널을 통해 조달되며 United States의 고객에게 신속하고 안정적으로 배송됩니다. Imtek Engineering은 경쟁력 있는 가격으로 정품 Valco 부품을 제공합니다. Valco FCM Flow Switch이 당사 웹사이트에 등록되어 있지 않더라도 언제든지 견적을 요청하실 수 있으며, 담당 팀이 신속히 답변 드릴 것입니다.
United StatesFlow Switch
FLOW
FCM
Flow switch
GENERAL CHARACTERISTICS The flow switch FCM was built to enable a simple control of the flow
rate and a fast signal in the absence of flow.
The electrical part is physically separate from the mechanical and the contact is magnetically actuated. The electric head has a
bayonet fixing system and, in case of necessity, can be replaced without removing the instrument from its installation.
● ● ● ● ●
No calibration needed.
Easy replacement of the electrical contact.
Low pressure loss.
Versions for both vertical and horizontal operation.
Can be used both with liquids and gases.
GV
Vertical mounting with flow direction from bottom to top.
GO
Horizontal or vertical mounting with flow direction from bottom to top
TECHNICAL DATA
Tab.1
Body Process connection Sensor Accuracy Max. Temperature Pressure loss Max. Flow rate
Max. pressure
Hexagonal bar Brass ½’’ Gas-M - UNI 228/1 Piston PP ± 15% of setting value
90°C 0,5 bar with max. flow rate 25 l/min All ranges 250 bar (*) Vertical
Horizontal 170 g
Mounting Weight
DIMENSIONS
mm.
Code 15 GV GO -
(*) Higher pressures on request.
AVAILABLE SETTINGS GV Settings l/min Nominal ON 0,8 0,8 1 1,1 1,5 1,7 2 2,1
2,5 2,6 3 3,2
Tab.2 GO Settings l/min Nominal ON 2,5 2,8 3 3,3 4 4,2 5 5,2 6 6,3 7 7,4
OFF 0,7 1 1,6 2 2,4 3,1
OFF 1,7 2 2,9 3,2 4,1 4,4
ELECTRICAL DATA Reed contact Reed contact data Connection
N.
6 5 1 2 3 4
Tab.3 N.O.
300 Vac Faston
No flow rate 70 VA 0,5 A 6,3 mm.
DIN plug protection IP65 On request The DIN cap is supplied in a separate kit
KIT
INSTALLATION AND MAINTENANCE Drain the hydraulic circuit before installation. Do not mount the
switch in direct contact with ferromagnetic surfaces.
Proceed with the assembly, taking care to use only a hexagonal wrench for fixing metal fittings.
In case of electrical failure replace the electrical head making sure of the happened hooking bayonet.
NOMENCLATURE
FCM 3 ●
2,5
15 GV
● ● KIT/FCM We reserve the right to change the data without notice
Tab.2 Tab.2 Tab.1 Tab.3
Name + N. of setting Nominal setting l/min Process connection + Type of installation
DIN cap optional mounting kit BE#040/8-03/2010
153
FCM
Flow switch
GENERAL CHARACTERISTICS The flow switch FCM was built to enable a simple control of the flow
rate and a fast signal in the absence of flow.
The electrical part is physically separate from the mechanical and the contact is magnetically actuated. The electric head has a
bayonet fixing system and, in case of necessity, can be replaced without removing the instrument from its installation.
● ● ● ● ●
No calibration needed.
Easy replacement of the electrical contact.
Low pressure loss.
Versions for both vertical and horizontal operation.
Can be used both with liquids and gases.
GV
Vertical mounting with flow direction from bottom to top.
GO
Horizontal or vertical mounting with flow direction from bottom to top
TECHNICAL DATA
Tab.1
Body Process connection Sensor Accuracy Max. Temperature Pressure loss Max. Flow rate
Max. pressure
Hexagonal bar Brass ½’’ Gas-M - UNI 228/1 Piston PP ± 15% of setting value
90°C 0,5 bar with max. flow rate 25 l/min All ranges 250 bar (*) Vertical
Horizontal 170 g
Mounting Weight
DIMENSIONS
mm.
Code 15 GV GO -
(*) Higher pressures on request.
AVAILABLE SETTINGS GV Settings l/min Nominal ON 0,8 0,8 1 1,1 1,5 1,7 2 2,1
2,5 2,6 3 3,2
Tab.2 GO Settings l/min Nominal ON 2,5 2,8 3 3,3 4 4,2 5 5,2 6 6,3 7 7,4
OFF 0,7 1 1,6 2 2,4 3,1
OFF 1,7 2 2,9 3,2 4,1 4,4
ELECTRICAL DATA Reed contact Reed contact data Connection
N.
6 5 1 2 3 4
Tab.3 N.O.
300 Vac Faston
No flow rate 70 VA 0,5 A 6,3 mm.
DIN plug protection IP65 On request The DIN cap is supplied in a separate kit
KIT
INSTALLATION AND MAINTENANCE Drain the hydraulic circuit before installation. Do not mount the
switch in direct contact with ferromagnetic surfaces.
Proceed with the assembly, taking care to use only a hexagonal wrench for fixing metal fittings.
In case of electrical failure replace the electrical head making sure of the happened hooking bayonet.
NOMENCLATURE
FCM 3 ●
2,5
15 GV
● ● KIT/FCM We reserve the right to change the data without notice
Tab.2 Tab.2 Tab.1 Tab.3
Name + N. of setting Nominal setting l/min Process connection + Type of installation
DIN cap optional mounting kit BE#040/8-03/2010
153
자주 묻는 질문
Valco의 Valco FCM Flow Switch에 관한 자주 묻는 질문입니다. Imtek Engineering은 United States에서 Valco의 Valco FCM Flow Switch를 조달하는 데 도움을 드릴 준비가 되어 있습니다.
Imtek Engineering은 신뢰할 수 있는 공급 채널을 통해 정품 Valco 제품을 조달하여 United States 고객에게 경쟁력 있는 가격으로 제공합니다.
