Industrial spare parts & engineering solutions since 2001.
독일에서 전 세계로 빠른 배송
다양한 결제 방법다양한 결제 옵션
- 제품
- B&R Automation
- 모듈
- B&R Automation X20DO9332 Module
B&R Automation X20DO9332 Module
기술 데이터시트 / 제품 문서
| 브랜드 | |
| 카테고리 | 모듈 |
| 제품명 | B&R Automation X20DO9332 Module |
| 제품 코드 | X20DO9332 |
저희에게 연락하세요! 영업일 기준 24시간 이내(주말 및 공휴일 제외) 재고 상태와 예상 납기를 안내해 드립니다.
제품 설명
B&R Automation의 B&R Automation X20DO9332 Module을(를) 포함한 제품은 병행 수입 채널을 통해 조달되며 United States의 고객에게 신속하고 안정적으로 배송됩니다. Imtek Engineering은 경쟁력 있는 가격으로 정품 B&R Automation 부품을 제공합니다. B&R Automation X20DO9332 Module이 당사 웹사이트에 등록되어 있지 않더라도 언제든지 견적을 요청하실 수 있으며, 담당 팀이 신속히 답변 드릴 것입니다.
United StatesTechnical description Order number Electrical properties Electrical isolation
X20DO9322
X20cDO9322
Channel isolated from bus Channel not isolated from channel and I/O power supply
Operating conditions Mounting orientation Horizontal Vertical Installation elevation above sea level
0 to 2000 m >2000 m Degree of protection per EN 60529 Ambient conditions
Temperature Operation Horizontal mounting orientation Vertical mounting orientation
Derating Starting temperature Storage Transport Relative humidity Operation
Storage Transport Mechanical properties Note
Yes Yes No limitation Reduction of ambient temperature by 0.5°C per 100 m
IP20
-25 to 60°C -25 to 50°C See section "Derating".
-
Yes, -40°C -40 to 85°C -40 to 85°C
5 to 95%, non-condensing Up to 100%, condensing 5 to 95%, non-condensing
5 to 95%, non-condensing Order 1x terminal block X20TB12 separately.
Order 1x terminal block X20TB12 separately.
Order 1x bus module X20BM11 separately.
Order 1x bus module X20cBM11 separately.
12.5+0.2 mm
Pitch
Table 2: X20DO9322, X20cDO9322 - Technical data 1) 2)
Number of outputs x RDS(on) x Nominal output current2. For a calculation example, see section "Mechanical and electrical configuration" in the X20
system user's manual.
At loads ≤ 1 kΩ
2.2 Status LEDs For a description of the various operating modes, see section "Additional information - Diagnostic LEDs"
in the X20 system user's manual.
Figure
LED r
Color Green
Status Off Single flash Blinking On Off Single flash
e
Red
e+r 1 - 12
Red on / Green single flash Orange
Description Module supply not connected
RESET mode
PREOPERATIONAL mode
RUN mode Module supply not connected or everything OK Warning/Error on an I/O channel. Level monitoring for digital outputs has
been triggered.
Invalid firmware Output status of the corresponding digital output
X20 DO 9322
2.3 Pinout
6
r e 1 2 3 4 5 6 7 8 9 10 11 12
DO 1
DO 2
DO 3
DO 4
DO 5
DO 6
DO 7
DO 8
DO 9
DO 10
DO 11
DO 12
X20(c)DO9322 Data sheet V 3.22
X20DO9322
X20cDO9322
Channel isolated from bus Channel not isolated from channel and I/O power supply
Operating conditions Mounting orientation Horizontal Vertical Installation elevation above sea level
0 to 2000 m >2000 m Degree of protection per EN 60529 Ambient conditions
Temperature Operation Horizontal mounting orientation Vertical mounting orientation
Derating Starting temperature Storage Transport Relative humidity Operation
Storage Transport Mechanical properties Note
Yes Yes No limitation Reduction of ambient temperature by 0.5°C per 100 m
IP20
-25 to 60°C -25 to 50°C See section "Derating".
-
Yes, -40°C -40 to 85°C -40 to 85°C
5 to 95%, non-condensing Up to 100%, condensing 5 to 95%, non-condensing
5 to 95%, non-condensing Order 1x terminal block X20TB12 separately.
Order 1x terminal block X20TB12 separately.
Order 1x bus module X20BM11 separately.
Order 1x bus module X20cBM11 separately.
12.5+0.2 mm
Pitch
Table 2: X20DO9322, X20cDO9322 - Technical data 1) 2)
Number of outputs x RDS(on) x Nominal output current2. For a calculation example, see section "Mechanical and electrical configuration" in the X20
system user's manual.
At loads ≤ 1 kΩ
2.2 Status LEDs For a description of the various operating modes, see section "Additional information - Diagnostic LEDs"
in the X20 system user's manual.
Figure
LED r
Color Green
Status Off Single flash Blinking On Off Single flash
e
Red
e+r 1 - 12
Red on / Green single flash Orange
Description Module supply not connected
RESET mode
PREOPERATIONAL mode
RUN mode Module supply not connected or everything OK Warning/Error on an I/O channel. Level monitoring for digital outputs has
been triggered.
Invalid firmware Output status of the corresponding digital output
X20 DO 9322
2.3 Pinout
6
r e 1 2 3 4 5 6 7 8 9 10 11 12
DO 1
DO 2
DO 3
DO 4
DO 5
DO 6
DO 7
DO 8
DO 9
DO 10
DO 11
DO 12
X20(c)DO9322 Data sheet V 3.22
자주 묻는 질문
B&R Automation의 B&R Automation X20DO9332 Module에 관한 자주 묻는 질문입니다. Imtek Engineering은 United States에서 B&R Automation의 B&R Automation X20DO9332 Module를 조달하는 데 도움을 드릴 준비가 되어 있습니다.
Imtek Engineering은 신뢰할 수 있는 공급 채널을 통해 정품 B&R Automation 제품을 조달하여 United States 고객에게 경쟁력 있는 가격으로 제공합니다.
