Eurotherm Temperature Controller
32H8E/32ENG

Custom text messaging
Specification
Custom messages can be created with iTools and downloaded to the 3200i to display when an event, alarm or process
condition occurs. This provides the operator with good visibility of what is happening in the process and provides messages
that they can understand and act upon.
General
Recipes iTools recipes can be created that can be used to change the operating parameters of the 3200i simply by
selecting a recipe using the 3200i push buttons. This is very useful where multiple products are processed but require
different parameters to be set. It can also be used to change the set-up of a indicator therefore allowing one unit to be used
as a spare for multiple applications.
Panel sealing:
Shock:
Vibration:
Altitude:
Atmospheres:
Analogue retransmission The measured process value can be retransmitted as either
a mA or voltage signal with a selection of outputs including 4-20mA and 0-10V dc. In the 32h8i this signal is isolated from
all other electronics within the unit.
Environmental performance Temperature limits
Operation:
Storage:
Operation:
Storage:
Humidity limits
0 to +55°C –10 to +70°C 5% to 90% RH (non condensing) 5% to 90% RH (non condensing)
IP65, Nema 4X
BS EN61010 2g peak, 10 to 150Hz <2000 metres Not suitable for use in explosive or
corrosive atmosphere
Electromagnetic compatibility (EMC) Emissions and immunity
BS EN61326
Electrical safety
BS EN61010
Installation cat. II; Pollution degree 2
INSTALLATION CATEGORY II The rate impulse voltage for equipment on nominal 230V mains is 2500V.
POLLUTION DEGREE 2 Normally, only non-conductive pollution occurs. Occasionally, however, a
temporary conductivity caused by condensation shall be expected Physical
Digital communication All units support both EIA232 and EIA485 communication
using the Modbus protocol as a slave device. It is also possible to digitally retransmit one parameter using a Modbus
broadcast to all other Modbus devices on the network.
Dimensions
3216i:
3204i:
32h8i:
3216i:
3204i:
32h8i:
48W x 48H x 90D mm 96W x 96H x 90D mm 96W x 48H x 90D mm 250g 420g 350g Mounting
Cut out dimensions 3216i: 1/16 DIN 45W x 45H mm 3204i: 1/4 DIN 92W x 92H mm
32h8i: 1/8 DIN, horizontal 92W x 45H mm
Weight
Panel
Configuration adaptor
PC configuration to all 3200i indicators can be achieved by using a configuration adaptor. It provides iTools with the ability
to communicate with and configure devices without any power being connected.
Operator interface Type Main PV display Lower display
3216i, 3204i:
32h8i:
3216i, 3204i:
32h8i:
Status beacons:
LCD TN with backlight 4 digits, green 5 digits, green or red 5 character starburst, green
9 character starburst, green Units, outputs, alarms
Power requirements 3216i: 100 to 230Vac, ±15%, 48 to 62 Hz, max 6W 24Vac, -15%, +10%.
24Vdc -15% +20% ±5% ripple voltage max 8W 32h8i, 3204i: 100 to 230Vac, ±15%
48 to 62 Hz, max 8W 24Vac, -15%, +10%.
24Vdc -15% +20% ±5% ripple voltage max 8W
iTools wizard Used to simplify the set up of 3200i series indicators, the
wizard guides the user through the configuration process with interactive help and graphical demonstrations of features.
Approvals CE, cUL listed (file E57766), EAC, FM, EN14597 TW approval number TW1222
Transmitter PSU (not 3216i) Rating:
Isolation:
24V dc, 20mA 264V ac double insulated
Communications Serial communications option Protocol:
Isolation:
Transmission standard:
3200i Series Indicators and Alarm Units
Modbus RTU slave Modbus RTU Master broadcast (1 parameter) 264V ac, double insulated
EIA232 or EIA485 (2 wire)
2