Aron VMPE16M3002 Valve

V.*.P PRESSURE CONTROL VALVES PLATE V.*.L PRESSURE CONTROL VALVES IN LINE
2 V.*.P / V.*.L...
V.*.P...
V.*.P.E...
CH. II PAGE 7 CH. II PAGE 8
V.*.L...
CH. II
BS.VMP...
PAGE
CH. II
9/10
PAGE
11
KEC.16/25...
CH. V PAGE 9
C*P.16/25...
CH. V PAGE 9
CETOP 3/NG06
SPOOLS FOR
CH. I PAGE 8 AD.3.E
V
Valve
*
M = maximum pressure S = sequence U = exclusion (areas rep. 1,15 : 1)
*
P = Plate mounting L = In line mounting
*
E = Presetting for solenoid valve Not for sequencing valve V.S.P...
(omit if not required)
*
Size (see overall dimensions) 16 - 25 = NG16 or NG25 161 - 251 = for V.*.L... only
(in line mounting valve) Type of adjustment:
M = Plastic knob C = Grub screw
*
Setting ranges 1 = 15 ÷ 45 bar (white spring) 2 = 15 ÷ 145 bar (yellow spring)
3 = 45 ÷ 400 bar (green spring)
**
00 = No variant V1 = Viton
AC = Exclusion valve for accumulators (only for VU*.**)
AQ = Presetting for XP3
2
PRESSURE - FLOW V.*.P.25
PRESSURE - FLOW V.*.16
CH. IV PAGE 9
ORDERING CODE
***
400 bar 15 ÷ 45 bar 15 ÷ 145 bar 45 ÷ 400 bar Max. flow V*P16...
150 l/min Max. flow V*P25...
350 l/min Hydraulic fluids Mineral oils DIN 51524 Fluid viscosity 10 ÷ 500 mm2/s
Fluid temperature -25°C ÷ 75°C Ambient temperature -25°C ÷ 60°C Max. contamination level class 10 in accordance
with NAS 1638 with filter ß25≥75 Drainage V*P16...
1 ÷ 2 l/min Drainage V*P25...
1 ÷ 2.5 l/min Dynamic pressure at drainage Max. 2 bar Weight V*P16... (without pilot valve)
3,3 Kg Weight V*P25... (without pilot valve) 7,4 Kg Weight V*L16... (without pilot valve)
4,6 Kg Weight V*L161... (without pilot valve) 4,5 Kg Weight V*L251... (without pilot valve)
7,7 Kg Weight V*L25... (without pilot valve) 8,3 Kg Spring 1 Spring 2 Spring 3
Serial No.
P (bar)
AM.3.VM...
CH. I PAGE 10 CH. I PAGE 11
Pressure max.
Setting ranges
P (bar)
STANDARD AD.3.E...
These pressure control valves are available in the basic VMP* maximum pressure, VSP* sequence and VUP* exclusion versions, with a single pressure
value and three calibration ranges that cover the band 15 ÷ 400 bar. It is possible to use auxiliary pilot valves, which
can be the simple standard AD3E solenoid valve, by the mere exchange of covers. These valves have been
fitted with an important safety feature for the operation of the system where
they are used; a mechanical end of stroke stop prevents the operator from
setting pressure values higher than those specified in the catalogue (it is
impossible to compress the spring completely). In the standard configuration
these valves are supplied with a 1.6 bar main spring and with calibrated ø1
mm pilot feed orifice (Variant part No.
00).
Subplate mounting valves are suitable for covers which do not conform to DIN
standards type C*P16/25.. whilst in line mounting valves are suitable for DIN
standards covers type KEC16/25...
Q (l/min)
Q (l/min)
The fluid used is a mineral oil with viscosity of 46 mm2/s at 40°C.
The tests were carried out at a fluid temperature 40°C.
HYDRAULIC SYMBOLS V.M.P.16.**...
V.M.P.25.**...
Maximum pressure valve Internal piloting and draining
V.S.P.16.**...
V.S.P.25.**...
Sequencing valve Internal piloting External draining
V.U.P.16.**...
V.U.P.25.**...
Exclusion valve External piloting Internal draining