im-tek.com

Solberg 375P Polyester Replacement Filter

Solberg

Product Code: 375P Polyester
Brand: Solberg



GET OFFER: info@imtek.com.tr

Description for Solberg 375P Polyester Replacement Filter

Product DescriptionSolberg Polyester 375P Filter Element with PrefilterElement Rating: 1500 SCFMSurface Area ft2: 28Inner Diameter: 8″Outer Diameter: 11 3/4″Height: 14 1/2″Endcap: Galvanized metal endcaps with neoprene gaskets on open end(s)Filtration: Polyester, 99%+ removal efficiency to 5 micronTemp (continuous): min -26°F (-15°C), max 220°F (104°C)Filter change out differential: 15-20″ H2O over initial Δ PSolberg Filter Element FeaturesPleated media for high dirt holding capacityReinforced with epoxy coated steel wire on both sides of cloth40 – 50% increased dust loading capacity with prefilter (part number suffix P)Optimal surface area per given sizePolyester Media BenefitsWashable with lukewarm water & mild detergentLess maintenance due to longer durabilityMoisture resistantHandles hot air and oil mist from unload cycle of reciprocating/piston compressorCleaning Solberg Filter ElementsSolberg filter elements should be cleaned or replaced once the pressure drop reaches 10 to 15-inches water column (250 – 380mm WC) above the initial pressure drop of the installation. Please note that the overall performance of a filter element is altered once cleaned; the initial pressure drop after cleaning will be greater than the original, clean pressure drop of the element. After each subsequent cleaning, the initial pressure drop will continue to increase. Under all circumstances, the initial pressure drop of the element needs to be maintained at less than 15-inches water column (380mm WC). Cleaned elements that exceed 15-inches water column (380mm WC) at start-up should be replaced with new elements.Paper Element: The paper element may be lightly blown with low pressure air. It is disposable and in most cases should be replaced with a new element.Polyester Element: The polyester element may be washed in warm soapy water, vacuumed, gently blown out or replaced. Use a mild detergent like Dawn liquid soap.  The element should be completely dry before reinstallation. The element should be replaced after a maximum of three cleanings.Polyurethane Prefilter: The prefilter may be washed as a sponge or replaced to give the element a longer service life.Epoxy Coated Wire Mesh and Stainless Steel Wire Mesh Elements: Cleaning instructions similar to polyester, except mild solvents may be used.

Recommended Products For Solberg


Solberg 375P Polyester Replacement Filter
Solberg CSL-850-200HC Vacuum Filter
Solberg CSL-850-201HCB Vacuum Filter
Vega VEGACAL 63 Capacitive Rod Probe for Continuous Level Measurement
Edur CV1/34-2900 Multi-Stage Inline Pump
Stenflex Type SF-11 DN 40 Expansion Joint
Gefran LT-M-0350-S 0000X000B00 Potentiometer
WARNER ELECTRIC E210 Shaft Mounted Clutches
KSB Amamix C4135/48 UDG Mixer
FIP Italy VRIM Series DN 15÷80 Check Valve
Eaton EDA 406 Duplex Filter
Ifm E40107 SI/1-1/2 NPT Screw-in adapter for process sensors
Grundfos NK 100-200/178 AA1F2AESBAQEKW3 Pump
Alwitco P60 6 Muffler
Micro Detectors NX16SR/XCN-AT1020 Area Sensor
Officine Orobiche PLD 150 Flow Alarm Switch
Scherzinger 5040-130-DM-55-6-Exe Hastelloy (R) Gear Pumps 5040
Ru-Steel F7 8” Elastics
Vulcanic 2206-77 Flange Immersion Heater
Edur CV10/3-2900 Multi-Stage Inline Pump
KSB MCPK150-125-315 GC NP2 A Pump
Hawe V30D-160 RKN-1-0-03/N Axial Piston Pump
Ru-Steel GDS 265 Autolubricants
Dynisco UPR90030000000 Process Indicator
Eltra EH63D250S8/24P8S3JR ENCODER, INPUT 5-30 VDC, INPUT CURRENT 5-500MA, 1 ENCLOSURE
Tecsis F2226 Tension/Compression Force Transducer
Weba BK500K Electrohydraulic Actuator