im-tek.com

Solberg CSL-850-201HCB Vacuum Filter

Solberg

Product Code: CSL-850-201HCB
Brand: Solberg



GET OFFER: info@imtek.com.tr

Description for Solberg CSL-850-201HCB Vacuum Filter

Product DescriptionSolberg Polyester 375P Filter Element with PrefilterElement Rating: 1500 SCFMSurface Area ft2: 28Inner Diameter: 8″Outer Diameter: 11 3/4″Height: 14 1/2″Endcap: Galvanized metal endcaps with neoprene gaskets on open end(s)Filtration: Polyester, 99%+ removal efficiency to 5 micronTemp (continuous): min -26°F (-15°C), max 220°F (104°C)Filter change out differential: 15-20″ H2O over initial Δ PSolberg Filter Element FeaturesPleated media for high dirt holding capacityReinforced with epoxy coated steel wire on both sides of cloth40 – 50% increased dust loading capacity with prefilter (part number suffix P)Optimal surface area per given sizePolyester Media BenefitsWashable with lukewarm water & mild detergentLess maintenance due to longer durabilityMoisture resistantHandles hot air and oil mist from unload cycle of reciprocating/piston compressorCleaning Solberg Filter ElementsSolberg filter elements should be cleaned or replaced once the pressure drop reaches 10 to 15-inches water column (250 – 380mm WC) above the initial pressure drop of the installation. Please note that the overall performance of a filter element is altered once cleaned; the initial pressure drop after cleaning will be greater than the original, clean pressure drop of the element. After each subsequent cleaning, the initial pressure drop will continue to increase. Under all circumstances, the initial pressure drop of the element needs to be maintained at less than 15-inches water column (380mm WC). Cleaned elements that exceed 15-inches water column (380mm WC) at start-up should be replaced with new elements.Paper Element: The paper element may be lightly blown with low pressure air. It is disposable and in most cases should be replaced with a new element.Polyester Element: The polyester element may be washed in warm soapy water, vacuumed, gently blown out or replaced. Use a mild detergent like Dawn liquid soap.  The element should be completely dry before reinstallation. The element should be replaced after a maximum of three cleanings.Polyurethane Prefilter: The prefilter may be washed as a sponge or replaced to give the element a longer service life.Epoxy Coated Wire Mesh and Stainless Steel Wire Mesh Elements: Cleaning instructions similar to polyester, except mild solvents may be used.

Recommended Products For Solberg


Solberg CSL-850-201HCB Vacuum Filter
Solberg CSL-850-200HC Vacuum Filter
Solberg 375P Polyester Replacement Filter
HFB BTL 3080 Two Bearing House
Alfamatic MOP 15 Press
Westcode N2083QK080 Phase Control Thyristors-Capsule
Tellarini ECC 12/25 521 Electric Pump
Megger Smart Thump ST Series 16 kV Portable Cable Fault Location System
Habasit XVT-1834 Belt
MBS MLW 114 7 25 1 6000 Sanitary Mixflo Multitube
Wilkerson P15-02-000A-F98 Regulator
Scherzinger 3030-110-B-ZK71-140 Stainless Steel Gear Pumps 3030
Fisher C804H-32 Internal Valve
Gefran LT-B-0900-P 0000X000A0N Potentiometer
Kelvion GVH 500H-AE Brazed Plate Heat Exchangers
Flojet D3732V5011ARL Diaphragm Pump
Leybold SV40 B Repair Kit
Faulhaber 23/1 112:1 Planetary Gearhead
Atos HQ023 Modular Valve
Meister RVM/UM Flow Monitor For Liquids
Meidinger 120-3 Blower
JVM JX 306-3220 Unbalance Motor
Grundfos DMX 280-8 B-SS/V/SS-X-E1A1A1XEMAG Dosing Pump
Gemü Gemü 88206287 Electro-pneumatic Positioner
Winsmith U2415S56 RD Speed Reducer
Alfa Laval 9613360418 UNIQUE SSV DN-80 012 RA W-W 0.8/BLASTED EPDM SHUT OFF NC
Felm FX 315XA-8 Motor