NSD VS-5FXG-1 VARICAM Cam Switch Output Controller

Model coding

VS-5FXG[1]-1

[1]Output systemCodeOutput systemBlankSink type

Contact us about other specifications.

 

ABSOCODER Basic Configuration

 SpecificationGeneral specificationItemSpecificationPower supply voltage24VDCPermissible power voltage range21.6 ? 30VDCPower consumption10W or lessInsulation resistance20M? or more between external AC power terminals and ground
(by 500 VDC insulation resistance tester)Withstand voltage500 VAC, 60Hz for 1 minute
between external DC power terminals and groundVibration resistance20m/s2 10 ? 500Hz, 10cycles of 5 minutes in 3 directions, conforms to JIS C 0040 standardAmbient operating temperature0 ? +55? (No freezing)
(Surrounding air temperature rating of 55? maximum)Ambient operating humidity20 ? 90 %RH (No condensation)Ambient operating environmentFree from corrosive gases and excessive dustAmbient storage temperature-10 ? +70?GroundingMust be securely grounded (ground resistance of 100 ohm or less)ConstructionInside control panelMountingSelect from two-screw mounting/DIN rail installation/
on-panel mounting using panel mounting fixture VS-K-F.Outside dimension (mm)130(W)×81(H)×99(D)MassApprox. 0.7kgPerformance SpecificationItemSpecificationConverter modelVS-5FXG-1Applicable sensorVRE-P028, VRE-P062Min. setting units0.5°Number of programs (Panel display)16Number of switch outputs40Number of multi-dogs10 times for each switch outputPosition data sampling time
(Permissible speed)None0.176ms(900 r/min when ON/OFF range is 1 degree)Effective number of switches:
5 points SW Nos. 1 ? 50.176ms(900 r/min when ON/OFF range is 1 degree)Effective number of switches:
10 points SW Nos. 1 ? 100.352ms(450 r/min when ON/OFF range is 1 degree)Effective number of switches:
5 points (ON/OFF independent) SW Nos. 1 ? 50.352ms(450 r/min when ON/OFF range is 1 degree)Switch output setting methodSettings are specified by numeric inputs or by teaching.Setting value memoryNon-volatile memoriesError detectionMemory error, Sensor error, No setting, Setting impossibleAdvanced angle functionPatternSettings by pointsNo. of points polygonal line20 points per switch (switch No.1 ? 10)Effective speed range0 ? 6000r/minResolution0.5°Speed setting unit1 r/minMax. advanced angle±180°Top dead center
stop angle functionPatternSettings by pointsNo. of points polygonal line30 points per programEffective speed range0 ? 6000 r/minNumber of programs
(Panel display)16Speed setting unit1 r/minMax. slippage correction range7200°Angle setting unit0.5°Communication function

Serial (RS-232C) communication (setting value saving or loading, monitoring, operation commands)

Connection by Mitsubishi-only protocol/MELSEC-A protocolConnection with angle display unit (NDP) is also possibleConnection by OMRON-only protocolConnection with touch panel is possible (VARIMONI)Auxiliary functionsExternal origin set function Timing pulse functionMotion detection switch output functionHysteresis functionProtected switch functionSwitch output enabling functionExternal error cancel inputArbitrary pulse output functionCurrent position value output (BCD, gray code (720-division)) / Speed output (binary code)Advanced angle functionTop dead center stop functionPassword functionEnhanced password functionMax. sensor cable lengthStandard100mRobotic(RBT)100mI/O spcificationItemVS-5FXG-1DescriptionInput signalsProgram No.4pointsInputs the exteral program No.Hold or external origin set1pointInput to prevent current position from changing or for origin setting.Error cancel1pointInput to cancel an error display.Switch output enable1pointSwitch signal will be output only upon the input of this signal.Slippage correction disabled1pointRelease the clutch for "Slippage correction" when using the top dead center stop function.Clutch ONN1pointON/OFF signal outputs occur in accordance with setting values.Output signalsSwitch outputs / Arbitrary pulse output40pointsON/OFF signal will be output based on the switch setting value, or pulse signal
will be output based on equally dividing a single rotation (division selectable from 1 ? 360).Timing pulse /
Motion detection switch1point60, 180 or 360 pulse signals will be output per rotation, or ON/OFF signal will be output based on the speed setting value.System ready1pointOutputs when controller and sensor are functioning normally.Program No.4pointsThe currently selected Program No. is output.Current position value
(BCD, gray code (720-division))
Speed Binary output11pointsCurrent position (3-digit BCD + 0.5-deg display) signal will be output, or rotational speed will be output in binary code.Latch pulse1pointOutputs a timing signal which ensures that the current position is read in a stable condition.Slippage correction1pointDuring top dead center control, the brake timing signal output is triggered by the clutch ON signal input.ItemInput specificationsItemOutput SpecificationsInput signalsProgram No.
External origin set
Current position HOLD
Error cancel
Switch output enable
Slippage correction disable
Clutch ONOutput signalsSwitch output or arbitrary pulse
Program No.
Sysytem ready
Slippage correctionMotion detection switch or timing pulseCurrent position value (BCD, gray code (720-division)) or speed (binary)
latch pulseInput circuitDC input, photo-coupler isolationOutput circuitTransistor (open-collector), photo-coupler isolationInput logicNegative logicOutput logicNegative logicNegative logicPositive logic*1Rated input voltage24VDCRated load voltage24VDC(30VDC max.)Rated input current10mAMax. load current100mA100mA10mAON voltage10VDC or moreMax. voltage drop when ON2.0V1.5V0.7VOFF voltage4 VDC or less

*1 : The output logic for current position and speed can be changed through parameter setting.

Cam Switch Output Controller