自2001年起提供工业备件与工程解决方案。
德国仓直发，全球快速配送
多种支付方式多种付款选项
Rickmeier R41/80 FL-K Pump
技术数据表 / 产品文档
欢迎联系我们！我们会在 24 个工作小时内（不含周末及节假日）确认库存状态和预计交期。
产品描述
Rickmeier的产品（包括Rickmeier R41/80 FL-K Pump）通过平行进口渠道采购，并快速可靠地交付给United States的客户。Imtek Engineering以具有竞争力的价格提供正品Rickmeier零部件。即使Rickmeier R41/80 FL-K Pump未在我们的网站上列出，您也可以随时申请报价——我们的团队将迅速响应并为您提供专属报价。
United States8 Technical data The technical data in this catalogue are intended for general information. During installation, operation and maintenance, the operating instructions and the information specified on the products
must be observed.
8.1 Operational limits The maximum permissible operating conditions for gear pumps in the standard version are described in the following. Contact RICKMEIER whenever it is necessary to exceed these specifications. In such cases, please contact our Sales department.
As a prerequisite for a long service life and maximum operational safety, the flow medium must retains its lubricity and, if possible, be clean and non-corrosive, but in any case must always be free
of hard admixtures.
Consideration must be given also to the following:
Properties Flow medium
Inlet pressure (constant pressure according to
DIN 24312)
Kinematic viscosity Degree of contamination (according to ISO 4406:1999, max.)
Gas content (undissolved, max.) Temperature (NBR seals) Temperature (FKM seals)
Radial shaft seal, standstill 4) Radial shaft seal during operation 4) Mechanical seal
Magnetic coupling
Min.
5 mm2/s 1)
-25 °C -25 °C -0.4 bar 5) -0.4 bar 5) -0.4 bar 5) -0.4 bar 5)
Max.
20000 mm2/s 1) 21/19/17 10 vol. % 2) 80 °C 150°C 3) 5 bar 0.5 bar 6) 10 bar 7)
16 bar 7)
Tab. 8: Operational limits of the standard design 1)
Depending on the application and operating conditions, lower and/or higher viscosities are possible, please
contact us.
2) Undissolved gas in the flow medium leads to increased noise emissions.
3) If used above 120°C, special measures may be required under certain circumstances (e.g., heat-resistant
clutch, pressure relief valve with heat-resistant spring, etc.); with optionally available sealing materials, different temperature ranges can be implemented.
4) Manometric 5) For speeds up to 1500 rpm, up to -0.5 bar permissible; in the short term: -0.6 bar (e.g., during start-up)
6) With optionally available radial shaft seal up to 6 bar 7) Versions for higher pressures available on request
22 / 52
TB3-NNNN-111 • 01
must be observed.
8.1 Operational limits The maximum permissible operating conditions for gear pumps in the standard version are described in the following. Contact RICKMEIER whenever it is necessary to exceed these specifications. In such cases, please contact our Sales department.
As a prerequisite for a long service life and maximum operational safety, the flow medium must retains its lubricity and, if possible, be clean and non-corrosive, but in any case must always be free
of hard admixtures.
Consideration must be given also to the following:
Properties Flow medium
Inlet pressure (constant pressure according to
DIN 24312)
Kinematic viscosity Degree of contamination (according to ISO 4406:1999, max.)
Gas content (undissolved, max.) Temperature (NBR seals) Temperature (FKM seals)
Radial shaft seal, standstill 4) Radial shaft seal during operation 4) Mechanical seal
Magnetic coupling
Min.
5 mm2/s 1)
-25 °C -25 °C -0.4 bar 5) -0.4 bar 5) -0.4 bar 5) -0.4 bar 5)
Max.
20000 mm2/s 1) 21/19/17 10 vol. % 2) 80 °C 150°C 3) 5 bar 0.5 bar 6) 10 bar 7)
16 bar 7)
Tab. 8: Operational limits of the standard design 1)
Depending on the application and operating conditions, lower and/or higher viscosities are possible, please
contact us.
2) Undissolved gas in the flow medium leads to increased noise emissions.
3) If used above 120°C, special measures may be required under certain circumstances (e.g., heat-resistant
clutch, pressure relief valve with heat-resistant spring, etc.); with optionally available sealing materials, different temperature ranges can be implemented.
4) Manometric 5) For speeds up to 1500 rpm, up to -0.5 bar permissible; in the short term: -0.6 bar (e.g., during start-up)
6) With optionally available radial shaft seal up to 6 bar 7) Versions for higher pressures available on request
22 / 52
TB3-NNNN-111 • 01
常见问题
关于Rickmeier品牌Rickmeier R41/80 FL-K Pump产品的常见问题。Imtek Engineering随时准备帮助您在United States采购Rickmeier的Rickmeier R41/80 FL-K Pump。
Imtek Engineering通过可信赖的供应渠道采购正品Rickmeier产品，并以具有竞争力的价格向United States客户提供。
