Zimm 199C0017 GSZ-150-RN KG63x10-RH-H160-KGF(FS)-GLP-KAR(E)-FB350(G)-FB350(S) Spindle Jack For Rotating Spindle

1
MSZ Alu series screw jacks, RN+RL
Trapezoidal screw Tr
M8/11.5deep (4x)
32H7/1.5deep
Screw length
Fitting height Y+stroke1)
Effective length= stroke+nut
MSZ-5-A-R rotating screw 5 kN
M6/8deep
made in Austria/EU 6890 Lustenau, www.zimm.at
MSZ-5-A-RN Type:
5 kN i = 4:1 static:
1800 rpm nmax:
Serial-no:
M8/11.5deep (4x) M8/11.5deep (8x)
Fitting height “Y” for 0-stroke, with Tr 18x4 screw
1)
All dimensions in mm
Flange nut FM
Duplex nut DM
Duplex nut
DM with SIFA
Self-aligning nut PM
Greasless nut FFDM
Bellows FB Y/A Y/A Y/A Y/A Y/A without bellows FB 153/100 163/113 188/138
196/145 171/121 2x Z-5-FB-265 – 211/136 233/158 244/168 219/144 2x Z-5-FB-500
– 341/201 363/223 374/233 349/209 2x Z-5-FB-800 – 381/221 401/243 414/253
389/229 Detailed instructions for determining the length can be found in catalogue XII (Section 8)
kN Technical data series MSZ-5-A-S / MSZ-5-A-R max. compressive/tensile force, static
max. compressive/tensile force, dynamic Nominal speed max. drive shaft speed
Screw size standard Gear ratio Housing material Worm shaft Weight of screw jack body
Weight of screw/m Gearbox lubrication Screw lubrication Gearbox operating temperature
Moment of inertia Input torque (at 1500 rpm) Drive-through torque
- 5 kN (500 kg)
- see duty cycle curves
- 1500 rpm
- 3000 rpm (depending on the load and duty cycle)
- Tr 18x42)
- 4:1 (N) / 16:1 (L)
- aluminium
- steel, case-hardened, ground
- 1.04 kg
- 1.58 kg
- grease lubrication
- grease lubrication
- max. 60°C, higher on request
- N: 0.217 kg cm2 / L: 0.117 kg cm2
- max. 4.7 Nm (N) / max. 1.5 Nm (L)
- max. 39 Nm
Drive torque MG (Nm) Breakaway torque Idling torque4) ML (Nm)
- F (kN) x 0.623)5) + ML (N-normal)
- F (kN) x 0.213)5) + ML (L-low speed)
- Drive torque MG x 1.5
- 0.10 (N-normal) / 0.08 (L-low speed)
Between gearbox and nut or nut and end of thread, provide for a safety distance
of (minimum) 10 mm!
See for the checklist in catalogue Screw Jack Systems XII (Section 7).
Important information
1) - extension if a bellows or spiral spring is fitted:
see the table or catalogue XII (Section 8)
2) - Tr 18x4 is standard, also available: stainless steel only for the R version: double-pitch, left-handed, increased screw Tr 20x4
3) - factor includes efficiency, ratio and 30% safety
4) - at 20°C, can be higher when new
5) - for a 4 mm screw pitch
© by ZIMM Austria 2014
3